1. Product OverviewTable 1: Basic Product SpecificationsParameterSpecificationTest MethodC
E-postadress: info@standard-groups.com
| Parameter | Specifikation | Test Method |
|---|---|---|
| Chemical Base | Modified silane | FTIR Analysis |
| Utseende | Clear liquid | Visual |
| Density (20°C) | 0.95-1.05 g/cm³ | ISO 2811 |
| Viscosity (25°C) | 10-50 mPa·s | DIN 53019 |
| Blixtpunkt | ≥65°C | ISO 2719 |
| Solid Content | 5-15% | DIN 53185 |
| pH Value | 4.5-6.5 | ISO 976 |
| Solvent System | Ethanol/Water | GC Analysis |
| Substrate Type | Surface Preparation | Adhesion Improvement | Recommended Cure Condition |
|---|---|---|---|
| PP/EPDM | Plasma treatment | 300-400% | 80°C × 30min |
| ABS | Solvent wipe | 200-250% | RT × 24h |
| Aluminum | Abrasion + degrease | 150-200% | 100°C × 15min |
| Glass | Alcohol cleaning | 180-220% | RT × 12h |
| Painted Surfaces | None required | 120-150% | 60°C × 45min |
Table 3: STD-7255 vs Alternative Adhesion Promoters
| Characteristic | STD-7255 | Silane-based | Titanate-based | Chrome-based |
|---|---|---|---|---|
| Environmental Impact | Low | Medium | Low | High |
| Substrate Versatility | ★★★★★ | ★★★ | ★★★★ | ★★★★ |
| Thermal Stability | 200°C | 180°C | 220°C | 250°C |
| Humidity Resistance | ★★★★★ | ★★★★ | ★★★ | ★★★★ |
| Application Method | Spray/Dipping | Spray | Brush | Spray |
| Cure Speed | Fast | Medium | Slow | Medium |
| VOC Content | <50g/L | 100-200g/L | <30g/L | 150-300g/L |
Surface Preparation:
Clean with isopropanol
Abrade non-polar surfaces
Maintain surface temperature 15-35°C
Application Methods:
Spray coating: 2-5μm wet film
Dip coating: 10-30 sec immersion
Brush application: Even coverage
Curing Parameters:
Air dry: 5-10 minutes
Force dry: 60-80°C for 5-15 minutes
Full cure: 24h at RT or 1h at 80°C
Key Advantages:
Excellent chemical resistance
UV stability
Low odor formulation
Water-based compatibility
Non-yellowing properties
Limitations:
Not for continuous immersion
Limited shelf life after opening
Requires dry storage
| Test | Method | Acceptance Criteria |
|---|---|---|
| Adhesion | ISO 2409 | Class 0-1 |
| Humidity Resistance | DIN 50017 | 500h no delamination |
| Thermal Cycling | SAE J1885 | 50 cycles stable |
| Salt Spray | ASTM B117 | 720h ≤2mm creepage |
| Peel Strength | ASTM D3330 | ≥4 N/mm |
| Aspect | Requirement |
|---|---|
| Storage Temperature | 5-30°C |
| Shelf Life | 12 months |
| PPE Requirements | Gloves, goggles |
| Ventilation | Required |
| Disposal | Hazardous waste |
Automotive interior/exterior trim bonding
Plastic-metal hybrid components
Electronic component encapsulation
Industrial composite manufacturing
Glass fiber reinforced plastics
Ansvarsfriskrivning: Ovanstående innehåll är endast för referens och kommunikation mellan branschinsider, och garanterar inte dess riktighet eller fullständighet. Enligt gällande lagar och förordningar och förordningar på denna webbplats ska enheter eller individer som köper relaterade artiklar erhålla giltiga kvalifikationer och kvalifikationsvillkor.
Företagstelefon
+86-21-6420 0566
Arbetstider
måndag till fredag
Mobiltelefon:
13816217984
E-post:
info@qinsun-lab.com
